Without experience installing an antenna is difficult. But you can figure it out yourself. If you have patience and do not want to pay installers for their services, then this instruction is for you. These same specialists had once been without experience and knowledge as you. But they learned their craft. Make an effort and you will succeed. Moreover, having trained on your antenna, you can provide services to your friends or relatives.
Be prepared for the fact that you can immediately fail. Perhaps the first setup and installation of the antenna may take a week, but then you can perform all these actions in a couple of hours. Before setting the satellite channels, you need to decide which satellite you will receive them from. Signals of the following devices are well received in Russia:. Hot Bird at Of course, there are other satellites, but these are in demand because of the large number of Russian-language channels.
On all other sites, there are no Russian channels or they are there, but in very small quantities. On mentioned there are both open channels and paid ones. In the list above, all paid packages where indicated in brackets. Channels and frequencies there are slightly different. Moreover, the encoding used is also different. The satellite, located at 56 degrees, is most of all focused on the eastern part of Russia. And the packages located in the position of 36 degrees — on the European part.
If you do not plan to buy cards for paid viewing or use sharing, then you need to choose such satellites, where many free channels are broadcast.
It did a scan for antenna. It did not pick up any channels. There are plenty of over-the-air channels in this area of southern New Hampshire. We are usong the flat RCA antenna on a Vizio tv we are getting all the local channels except for ,, They are offered in our area. We just moved but got them all from where we moved from. Any suggestions? I had channels before but i was missi g some so i tryed rescaning and that where i lost all my channels.
I was told at Best Buy that I have to have a receiver box to between the antenna box and the tv. Im using a antenna to my vizio im getting all the channels it connect to beside four. I hope! You must be logged in to post a comment. Setting Up Cable or Satellite Service There are different steps for activating cable or satellite service depending on whether or not you have a cable box or satellite box connected to the TV.
The panel will look like a square box with one end open. Add a washer and nut on the end of each bolt after tightening them. This slot is what you use to point the satellite up or down. Fit the U-shaped rod inside the adjustment panel.
Your dish will have a bent metal rod that fits into one of the slots on the adjustment panel. Slip the rod inside, sliding its prongs through the holes. Ensure the prongs point toward you rather than the tail end of the LNB rod you connected earlier.
Fit a small clamp over it, followed by a washer and nut on each prong. The adjustment panel has 3 different slots. Use the slots to reposition the satellite dish. In most cases, the middle slot is best for setting the dish at the proper angle. Bolt the antenna bracket to the back of the satellite dish.
You have a couple more bolts to add to finish the bulk of the assembly, and this is one of the easiest parts to finish. Line up the holes on the plate with the holes on the back of the dish. Stick the longest bolts you have, usually 2 to 3 in 5. Then, place a washer and nut on the end of each bolt, tightening it with your wrench.
If they feel shaky, carefully separate them and tighten the bolts. One last component, the LNB, controls the dish's functionality. First, slide the handle of the LNB onto the open end of the arm. Secure it with nuts and bolts, then take the LNB out of the box. It looks almost like a round speaker or flashlight. Position it on the handle, facing it toward the dish before bolting it in place. You may need to loosen the LNB later to readjust it and improve the signal quality.
Connect the adjustment panel on the dish to the wall mount. Fit the dish onto the open end of the support. If everything is attached correctly, it will fit inside or behind the adjustment panel.
You can then add the 1 or 2 remaining bolts to fasten these pieces together. If the dish looks good, then you're ready to position it to communicate with a satellite. If the mount is meant to attach to the back of the panel, your satellite will also come with a pair of clips. Position them behind the support, then add the screws through them to bind the parts together. Part 3. Select a satellite you wish to connect to. Pick a satellite that is in range of your particular dish.
There are numerous satellites out there, but dishes cannot get signals from all of them. If you bought your dish from a TV service, for instance, you might have a hard time connecting to their competitor's satellites.
Tracking sites list the names, which usually include the owning company or the service they provide. If you bought a satellite service, it is possible to receive satellite signals outside that service. Since you usually need to replace several parts, it's easier to get a new satellite instead.
Try to pick a satellite close to your area. If you subscribe to a particular TV service, you will need to use the company's satellites. The biggest providers have multiple satellites. Find the satellite's location before positioning the dish. You're going to need to point the dish in the correct direction, then angle it up at the sky. This isn't easy to do if you don't know the satellite's positioning. Fortunately, satellites don't move much, so you can use a positioning database to adjust your dish.
The site will give you the precise positioning needed for your dish to receive the signal. You won't be able to receive a signal from a distant satellite.
Don't expect to reach a Chinese satellite if you're in North America, for instance. Use the azimuth number to rotate the satellite. Have a compass handy and locate true north first. Then, look at the azimuth number and find where that is on the compass.
North is considered 0 degrees, east is 90 degrees, south is degrees, and west is degrees. Rotate the satellite dish horizontally until it points in the correct direction. Then, turn the satellite southwest from there. Move the dish vertically to adjust its elevation. Once you know the height needed to reach the satellite, go behind the dish. Last Updated: May 29, Approved. This article was written by Jack Lloyd. He has over two years of experience writing and editing technology-related articles.
He is technology enthusiast and an English teacher. This article has been viewed , times. Select a network. Make sure you can receive your satellite's signal. Install the receiver dish. Point the dish toward your satellite. Install the tuner and adjust the axes.
Connect the dish to the receiver. Connect the receiver to your TV. Search for channels. Did this summary help you? Yes No. Log in Social login does not work in incognito and private browsers. Please log in with your username or email to continue.
No account yet? Create an account. Edit this Article. We use cookies to make wikiHow great. By using our site, you agree to our cookie policy. Cookie Settings. Learn why people trust wikiHow. Download Article Explore this Article parts. Related Articles. Article Summary. Part 1. All rights reserved. This image may not be used by other entities without the express written consent of wikiHow, Inc. Select a satellite network.
In order to check your satellite's compatibility with your current location, you'll have to know the name of the satellite itself.
Make sure that you can receive your satellite's signal. Before attempting to set up an FTA system, you should know if it's possible for you to receive your selected satellite's signal. Select your satellite's name from the drop-down box on the right side of the page. Click Search! Make sure that there is a green line indicating line-of-sight for your satellite.
If this line is red, the satellite won't work properly in your area.
0コメント