The following steps may NOT be of any use if the mast is not perpendicular to the ground. Now, we need to setup the Elevation and the Skew angles of the dish. For Toronto and adjacent areas, you can safely assume the Skew angle to be 96 degrees and the Elevation to be 40 degrees. The elevation can slightly vary depending on the area and how the dish and the mast are installed but you can leave the Skew angle untouched.
For other areas of Canada, please refer to page 34 on this chart. If you follow the two steps above correctly, half of your job is done when it comes to pointing.
Assuming that most of you will be using your receiver TV box to point your satellite dish and not a satellite meter, one thing that will make pointing easier is if you can use a standard definition SD receiver like , etc. Reason being that the standard receivers process the signal much faster. The connection between the LNB and the receiver must be direct meaning no switches or splitters.
On the TV, set the satellite to 91 and the transponder to 1. During your installation appointment the Bell technician will do the following:. Bell Install is a hassle-free way to ensure your Bell Satellite TV service is installed and operating correctly.
A Bell Satellite TV technician will come to your home and take care of everything, at your convenience. Depending on your requirements, installation may take between 2 to 3. Available to residential customers where technology permits.
Subject to change without notice and cannot be combined with any other offer. Taxes extra. Other conditions apply, including minimum system requirements. Basic installation includes professional satellite installation and the connection and activation of up to three receivers.
Installation of a multi-satellite dish upgrade is performed at no charge. For more information, see the complete installation outline. In our ongoing efforts to improve our support section, your opinion is invaluable. Please let us know what we did well or what we can improve about this article. If you require assistance, please Contact us.
Your current region: Ontario. Your current region: Ontario Change Select a region:. Need help? What is Bell Install? What the Bell Satellite TV technician will do.
What the Bell Satellite TV technician will do During your installation appointment the Bell technician will do the following: Install your dish, cabling up to feet of RG-6 cable 1 and satellite system.
Ground your system. Program your universal remote and show you how to use it. The satellite dishes are not all the same: some do not even have a parabolic shape. You must choose the right satellite dish size in order to get maximum coverage. The most common are 60, 80, and cm in diameter. Its design is also very important because it can determine the power and quality of reception. In addition to the type of antenna, another important point is the size: the lower the quality of the satellite signal in our geographical area, the greater the plate should be.
These are the most common types of satellite antenna dishes :. The LNB This device Low Noise Block , literally translated as a low noise block is used to process the signals emitted by the satellites and convert them into a lower frequency so that they can be distributed smoothly to the receiver. The image quality on the screen will depend on its quality.
These devices can be:. The support of the LNB. It is the arm at whose end the LNB is placed stably so that it can be oriented according to the reception parameters. It is attached to the wall bracket, to the mast of a collective antenna, or to the mast of the floor of a terrace, usually by means of U-bolts or very resistant jaws.
It is also used to place the plate anchors and the height adjustment systems of the plate. The height regulator It allows to orientate the height of the plate for the correct reception according to the satellite. It has some through screws with nuts that can be loosened and tightened to adjust the orientation. The azimuth regulator. The wall or mast support usually a cylindrical tube is the axis that allows the azimuth to be adjusted with respect to the satellite, starting from the north cardinal point or the magnetic north.
To do this you have to rotate the structure with the plate around it. Its manipulation allows to capture the satellite signals, combining it with the height of the parabola. The azimuth adjustment is made clockwise or counterclockwise. The wire. When installing a satellite dish, it is essential to use the correct cable. You must use a coaxial cable of satellite quality, somewhat thicker than the one used inside, with its corresponding connectors.
In the cable sheath you will find information about its uses. The satellite receiver It is the device that transforms the signal received by the antenna so that it can be seen on televisions. It is the point at which the coaxial cable arrives from the satellite dish, and from which the cable that goes to the TV comes out. It is best to make this connection with HDMI, so that there is no loss of sharpness in the image. In addition, with a cable or wireless connection you can receive Internet services that are contracted with the telephone company.
Does your building have a home automation network and do you want to install a satellite dish? The installation wiring can be used to channel the antenna cable to your home if they give you the corresponding authorization. In a single-family home, you will only have to attend to the possible urban norms.
Once each part of the kit has been identified, it is time to mount the parabolic and then install it at the appropriate point. In general, the steps are as follows:. Step 1. Fix the anchor legs of the support to the back of the plate: normally it is placed with four through screws and four nuts.
0コメント